TDU 107 Extended

TDU 107 Extended

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

1.4.3.0

Changes

  •  Added support for two additional nominal settings buttons.

Corrections

  • Fixed communication issues with AGC v6.15.x.

1.4.3.0

13/12/2024

Changes

  •  Added support for two additional nominal settings buttons.

Corrections

  • Fixed communication issues with AGC v6.15.x.

1.4.2.1

14/10/2024

Corrections

  • Fixed issue with home page application drawing becoming zoomed out with every power cycle or reboot from TDU restart.
  • Fixed issue with TDU not connecting with AGC-4 Mk II application software version 6.14.0.
  • Fixed show/hide of page 2-3 in home.
  • Resolved issue with inhibit start button, inhibit stop button, inhibit GB/TB button and inhibit MB button commands.

1.4.2.0

11/06/2024

New features

   1- Confirm action pop-ups.

 

Changes

   1- New method for handling translations.
   2- Tier 4 jump improvements.

 

Corrections

   1- Fixed issue with parameter dialogue not showing the correct state of the toggle switches.

1.4.1.0

04/01/2024

New features

        • Support for ASC-150.
          Support for ASC-4

1.4.0.0

26/10/2023

New features

      • Supervision variant for TDU.

Changes

      • Extended capability to read more VTA's.

Corrections

      • Fixed issue with TDU not being able to connect to AGC-4 Mk II v6.08.0.
        Fixed issue with TDU not being able to connect to AGC-4 Mk II BTB.

1.3.12.0

25/08/2023

New features

    • Supervision shows ASC controllers.

Changes

    • Added support for Volvo EMS.

Corrections

    • Fixed TDU 107 supervision issue.

1.3.11.1

20/06/2023

Changes

    • Fixed missing application supervision when there is a BTB controller in the application drawing.

1.3.11.0

05/03/2023

New features

  • Added support for FPT stage V engines.

Changes

  • Created separate pages for "Engine lamps" and "Exhaust aftertreatment".
  • Added support for tree view translations.
  • Made opening parameters more intuitive.

1.3.10.1

07/10/2022

Corrections:

1- Fixed horizontal scrolling of Supervision.
2- Fixed missing "None" option in "Instrument Selection".
3- Fixed missing Custom Logo in "Log" and "Controller settings" pages.
4- Reset index when changing between "Controller settings" lists.

1.3.10.0

13/07/2022

Changes:

  • Logo implementation and top bar branding.
  • Branding configuration import and export.

Corrections:

  • Fixed glitch with negative values in alarm and event log.
  • Fixed glitch with controller communication lost for 1-2 seconds every 13 or 25 minutes.
  • Fixed glitch with TDU not able to connect to AGC-4 Mk II Mains controller.

1.3.9.1

17/02/2022

Changes:

  • Only show measurements supported by the connected ECU.

Corrections:

  • Fixed issue with writing alarm settings for parameters

1.3.9.0

12/01/2022

Changes:

  • New application select page added to the setup menu.

Corrections:

  • Toggle switches are more accurate now.
  • Fixed language export issue with empty AOP labels.
  • Fixed missing semi button when activating the German AUS mode.

 

1.3.8.0

06/12/2021

Changes:

  • Added option to hide application and nominal settings on instrument pages.
  • New and updated customer branding.

Corrections:

  • IP can't be changed when disabling Master/slave when TDU is connected to slave.

1.3.7.0

31/05/2021

New features:

  • Support for OEM product IDs in AGC-4 Mk II is added.
  • Scania EMS S8 support is added.
  • Block mode button is added.
  • Master/slave controller manual switch is added.

Changes:

  • "AUS" mode for German option V0108 in "Auto" and "Test" mode is added.

Corrections:

  • Alarms are removed from the header when alarm conditions disappear.
  • Fixed an issue with missing genset modes in the language file.
  • Fixed that the genset mode would change if the password level was set to service or master.

1.3.6.0

23/03/2021

New features:

  • Added support for OEM product IDs in AGC-4 Mk II.
  • Extra safety pop up (Nominal setting + Plant mode).
  • Translation file added with "TDU specific texts".
  • "UpdatePackage.zip" includes software version.
  • Support updatepackage.zip with lower case characters.

1.3.5.0

29/01/2021

New features:

  • Added support for AGC-4 Mk II
  • Added customer branding

1.3.3.0

10/09/2020

Supported on AGC-4 DG & AGC-4 Mains.
Minimum AGC-4 SW required: 4.74.3.
Recommended minimum AGC-4 SW: 4.76.1.

New features:

  •    Further brandings are added.
  •    AGC-4 as clock master is added.

Changes:

  •    New entry point for the ECU measurement window is added.

Corrections:

  •    Parameter max. value was not taken into account for text values.
  •    If exactly 9 alarms were present, the last one was not visible.
  •    Possibility to include system information when exporting a TDU.config file is added.
  •    Preventive measures were taken to stabilize the VNC connection.
  •    Generator measurements are removed from mains TDU.
  •    Regeneration parameters are added to TDU.
  •    Application supervision now supports mains with id´s 1-16 and DG´s with ID 17-32.
​

1-3-2-0

17/06/2020

Supported on AGC-4 DG & AGC-4 Mains.
Minimum AGC-4 SW required: 4.74.3.
Recommended AGC-4 SW: 4.76.1.

New features:

  • EIC measurements can now be seen in a separate window.
  • Added support for new Boolean measurements.

Changes:

  • More texts have been included in the translation file, to extend translation capabilities of the TDU. (Controller texts and Engine DM1/DM2 texts).
  • Sync shortcut on the home screen now only requires a single press instead of a long press.
  • Internal references to measurement layout on Modbus have been updated.
  • Preferred font have been removed from the CSV file.

Corrections:

  • Current status of the DG on the alternator curve now works properly.
  • TDU Supervision is now updated correctly when using the Easy connect feature.
  • Empty AOP texts are now saved during power cycle or in TDU.config files.
  • "Autojump to sync scope" is now saved during power cycle or in TDU.config files.
  • The screensaver now shows the "Connection lost" message.
  • The branded splash screen is now shown correctly.

1.3.1.0

19/02/2020

Supported on AGC-4 DG & AGC-4 Mains.
AGC-4 SW required: 4.76.1.

New features:

  •    Control panel instruments can now be custom scaled by pressing and holding for 3 seconds.
  •    All voltage selections in parameter 9030 are now supported.
  •    Access lock implemented; when the input is configured and active in the controller all settings are read only in the TDU.
  •    New screen is added with current measurements shown graphically.
  •    M-logic command "Inhibit. mode button" is now reflected in the TDU.
  •    It is now possible to add a separate password for control panel instruments under "Permissions".
  •    Fuel level is now shown in the top bar, if parameter 10980, 10990 or 11000 is set to "RMI fuel level" via the utility software.
  •    Running hours is now shown in the top bar, if connected to a genset controller.
  •    Parameter shortcut is added on the control page; it can be enabled/disabled under "Display settings".
  •    Power Management ID and priority are added to the home screen, when connected to a genset controller.
  •    Auto Jump to Synchroscope page is added; it can be enabled/disabled under "Display settings".
  •    Import/ Export: It is now possible to load a configuration file from an older software version.

Changes:

  •    20 pages are now available in the instrument panels on the control page.
  •    Lists of instrument measurements have been expanded.
  •    User access level filtering on the parameter page have been removed.
  •    DM1/DM2 texts have been expanded.
  •    When connected to a German AGC-4 with V0108 option, the manual button is removed.

Corrections:

  •    Language management create export has been corrected, when specific German characters are used in the controller translation.
  •    Visibility of the DM1 top icon has been corrected.

1.3.0.1

23/09/2019

Only supported on AGC-4 DG & AGC-4 Mains.
Minimum AGC-4 SW required: 4.74.3.

Corrections:

  • Corrected: AOP shortcut on control panel page.
  • When changing mode, the confirmation dialogue now always pops up.

1.3.0.0

12/09/2019

Supports AGC-4 DG & AGC-4 Mains controllers.
Minimum AGC-4 SW required: 4.74.3.

New features:

  • Support of AGC-4 mains controller.
  • Import/export of following settings via USB:
            - Meters on homepage
            - Password levels
            - AOP texts
            - All settings under "Display config" 
  • Added "Connection to controller" text on start-up screen.

Changes:

  •    TDU backlight timeout introduced.
  •    Fixed sporadic communication timeout messages on TDU.
  •    Extended number of status texts on the TDU.

Corrections:

  • Fixed screensaver freeze issue.
  • Corrections to some status texts.
  • Fixed rare initial communication issues.
  • Create new master language function corrected

1.2.2.0

19/06/2019

Only supported on AGC-4 DG.
Minimum AGC-4 SW required: 4.72.0.

Changes:

  • Internal production handling updated.

1.2.1.0

12/06/2019

Only supported on AGC-4 DG.
Minimum AGC-4 SW required: 4.72.0.

New features:

  • Implementation of offline USB update of TDU
  • Added scrolling on supervision page
  • Added hardcoded master password to DM1/DM2 clear button
  • Enhanced user feedback during restart of TDU
  • Added new EasyConnect text: "DG Ready to be added"

Changes:

  • Improved connection stability between TDU and AGC-4 controller
  • Change scaling of Fuel rate measurement

Corrections:

  • Correct Modbus offset for escape mode timer
  • Improved stability of auto connect feature
  • Added missing password prompt to AOP shortcut on home screen
  • Fixed misplaced buttons in control panel

On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).

Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.

DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.

DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.

Licence agreement for software downloaded from www.deif.com

Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.

The latest versions for full functionality

As always, we recommend that you install our offered improvements to fully utilise your DEIF product.

All improved software can be downloaded at your convenience at www.deif.com under “Software”.

Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.